Peugeot 208 Key Replacement
Peugeot 208 key replacement is best left to experienced auto locksmiths who have the proper tools and know-how. They can create and program new keys much faster than a dealership would and at a lesser cost.
A dead battery for your coin is most likely to be the cause the reason why your key fob isn't locking or unlocking the doors. However, there are other reasons why the key might be malfunctioning.
Dead Coin Battery
A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also hindering it from starting the engine. If this is the case, you'll need to make use of the backup starting procedure that is described in the owner's manual to your vehicle.
The spark plugs might also be worn out. The spark plugs are responsible to ignite the fuel that starts the engine. However they are limited in their time of life. They'll eventually degrade when they aren't used enough.
Luckily, there's an easy solution for this issue. The best way to solve this issue is to determine the voltage of your car battery using a multimeter. If the voltage is lower than 11,5 volts, then it's time to replace it. It is also necessary to clean the contacts of the battery when it has corrosion. peugeot key fob can be accomplished by removing the rubber cover from the two battery terminals and then using a wirebrush to clean any corroded battery parts. Then, you should reconnect the positive pole cables to the negative.
Water Damage
If your 208 won't turn on and the battery isn't empty, you must ensure whether the spark plugs work. You may find that they're dirty and they don't spark. This can be fixed by cleaning the spark plugs in a workshop.
Peugeot cars are equipped with keys that are transponder-type and works with the car's ignition system. This ensures that only a valid key is able to turn the engine. If the chip inside the Peugeot key is damaged, it won't transmit the proper signal to the vehicle.
Water damage is a typical cause of this issue. This is a common problem in warmer climates where the vehicle has been exposed to snow or rain. In this case, contact a reliable locksmith who will have the tools and equipment needed to reprogram the key. They will also have the most up-to-date technological know-how and machinery required to create the Peugeot 208 smart key. The process should take no more than 15 minutes.
Contacts to the battery are not working properly.
Peugeot changed from the old carbon-encased transponder chips to a new type of chip that uses electronic components on circuit boards. This new system works well when it's fresh, but as time passes, the circuit boards begin to degrade and stop working properly.
This could stop the immobiliser from working, so your vehicle will not start. Contact a Peugeot specialist or a locksmith, if this is the case.
A common issue is when the battery of the key fob starts to fail. This causes the blade of the key to stop feeding into the lock. A locksmith from your car will replace the battery and then cut a new blade for you. This is a simple solution.
Faulty Receiver Module
If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden rain or accidentally washing it the wrong way, it could be due to a malfunctioning receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer which controls the central locking system of your Peugeot vehicle.
Rubber seals on the key fob prevent water from getting to the electronic chip. However, prolonged exposure to water can be able to penetrate these seals and cause damage to the chip. Submerging the key fob into ocean water at the beach or throwing it into the pool could be particularly damaging due to the high salt content.
If your Peugeot spare key fob stops working it is necessary to have the module replaced. This is only done by an Peugeot specialist or a professional auto locksmith. Peugeot keys, unlike other cars, are protected by an immobilizer system. This requires the proper programming to allow the car to start. This is the reason that you should only rely on a Peugeot locksmith to design and program the replacement.
Faulty on-Board computer
The computer on the board of your Peugeot is responsible for a number of the systems in your car, from power windows to airbags. The on-board computer displays a code when something goes wrong. The code will be stored within the system until the problem is resolved. In most cases, this will require replacing the onboard computer.
The most frequent cause for the warning light of the airbag to flash is corrosion or loose connections in the sensor. This can be caused by wear and tear, aging, or exposure to moisture and salt. This issue needs to be dealt with as soon as you can, since an airbag that's malfunctioning could pose danger in the event of an accident.
If you find the error "card not found" on your Peugeot key fob, the battery inside the key fob may be weak or dead. This can prevent the key fob from sending a signal to disable the standard immobilizer in your vehicle. Test this by pressing the unlock button on the fob's key, then trying to start your vehicle. If it doesn't work the battery on the key has to be replaced.